Extraordinary transport behavior of gases in isothermally annealed poly(4‐methyl‐1‐pentene) membranes

Poly(4‐methyl‐1‐pentene) (PMP) membranes were modified through isothermal annealing to investigate the change of their crystalline structure and rigid and mobile amorphous fractions (RAF and MAF), assuming a three‐phase model, affected the gas transport behavior. The crystalline structure was characterized by wide‐angle X‐ray diffraction (WAXD) and small‐angle X‐ray scattering (SAXS) techniques, and the free volume properties were analyzed by positron annihilation lifetime spectroscopy. Compared with the pristine membrane, the annealed membranes show higher crystallinity; the crystals undergo partial structural change from form III to form I. The lamellar crystal thickness, rigid amorphous fraction thickness, and long period in the lamellar stacks increase with crystallinity. The annealed PMP membranes exhibit higher permeability due to the increase in larger size free volumes in MAF and higher selectivity due to the increase in smaller size free volumes in RAF, respectively. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 2368–2376     

Redox‐Active Tetraruthenium Macrocycles Built from 1,4‐Divinylphenylene‐Bridged Diruthenium Complexes

Metallamacrocylic tetraruthenium complexes were generated by treatment of 1,4‐divinylphenylene‐bridged diruthenium complexes with functionalized 1,3‐benzene dicarboxylic acids and characterized by HR ESI‐MS and multinuclear NMR spectroscopy. Every divinylphenylene diruthenium subunit is oxidized in two consecutive one‐electron steps with half‐wave potential splittings in the range of 250 to 330 mV. Additional, smaller redox‐splittings between the +/2+ and 0/+ and the 3+/4+ and 2+/3+ redox processes, corresponding to the first and the second oxidations of every divinylphenylene diruthenium entity, are due to electrostatic effects. The lack of electronic coupling through bond or through space is explained by the nodal properties of the relevant molecular orbitals and the lateral side‐by‐side arrangement of the divinylphenylene linkers. The polyelectrochromic behavior of the divinylphenylene diruthenium precursors is retained and even amplified in these metallamacrocyclic structures. EPR studies down to T=4 K indicate that the dications 1‐H²⁺ and 1‐OBu²⁺ are paramagnetic. The dications and the tetracation of macrocycle 3‐H display intense (dications) or weak ( 3‐H⁴⁺ ) EPR signals. Quantum chemical calculations indicate that the four most stable conformers of the macrocycles are largely devoid of strain. Bond parameters, energies as well as charge and spin density distributions of model macrocycle 5‐H^Me were calculated for the different charge and spin states.     

Lattice Boltzmann simulation of liquid–vapor system by incorporating a surface tension term

In this study,we investigate the pseudopotential multiphase model of lattice Boltzmann method(LBM)and incorporate a surface tension term to implement the particle interaction force.By using the Carnahan–Starling(CS)equation of state(EOS)with a proper critical pressure–density ratio,a density ratio over 160000 is obtained with satisfactory numerical stability.The added surface tension term offers a flexible choice to adjust the surface tension strength.Numerical tests of the Laplace rule are conducted,proving that smaller spurious velocity and better numerical stability can be acquired as the surface tension becomes stronger.Moreover,by wall adhesion and heterogeneous cavitation tests,the surface tension term shows its practical application in dealing with problems in which the surface tension plays an important role.     

Numerical simulation of droplet ejection of thermal inkjet printheads

In this study, we present a method to predict the droplet ejection in thermal inkjet printheads including the growth and collapse of a vapor bubble and refill of the firing chamber. The three‐dimensional Navier–Stokes equations are solved using a finite‐volume approach with a fixed Cartesian mesh. The piecewise‐linear interface calculation‐based volume‐of‐fluid method is employed to track and reconstruct the ink–air interface. A geometrical computation based on Lagrangian advection is used to compute the mass flux and advance the interface. A simple and efficient model for the bubble dynamics is employed to model the effect of ink vapor on the adjacent ink liquid. To solve the surface tension‐dominated flow accurately, a hierarchical curvature‐estimation method is proposed to adapt to the local grid resolution. The numerical methods mentioned earlier have been implemented in an internal simulation code, CFD3. The numerical examples presented in the study show good performance of CFD3 in prediction of surface tension‐dominated free‐surface flows, for example, droplet ejection in thermal inkjet printing. Currently, CFD3 is used extensively for printhead development within Hewlett‐Packard. Copyright © 2015 John Wiley & Sons, Ltd.     

Orientation dependent size effects in thermal buckling and post-buckling of nanoplates with cubic anisotropy

In this work, a continuum model is presented for size and orientation dependent thermal buckling and post-buckling of anisotropic nanoplates considering surface and bulk residual stresses. The model with von-Karman nonlinear strains and material cubic anisotropy of single crystals contains two parameters that reflect the orientation effects. Using Ritz method, closed form solutions are given for buckling temperature and post-buckling deflections. Regarding self-instability states of nanoplates and their recovering at higher temperatures, an experiment is discussed based on low pressurized membranes to verify the predictions. For simply supported nanoplates, the size effects are lowest when they are aligned in [100] direction. When the edges get clamped, the orientation dependence is ignorable and the behavior becomes symmetric about [510] axis. The surface residual stress makes drastic increase in buckling temperature of thinner nanoplates for which a minimum thickness is pointed to stay far from material softening at higher temperatures. Deflection of [100]-oriented buckled nanoplates is higher than [110] ones but this reverses at higher temperatures. The results for long nanoplates show that the buckling mode numbers are changed by orientation which is verified by FEM.     

椭圆偏振法测定在线Low-E玻璃的可见-近红外光学常数与膜厚

从在线Low-E玻璃光学机理出发,用椭圆偏振光谱仪对在线Low-E玻璃功能层和过渡层的可见-近红外波段的光学常数进行研究.测量了样品在三个不同入射角的椭偏参数,分别用Lorentz双振子模型和Cauchy模型来描述Low-E玻璃功能层和过渡层的光学色散特性.通过拟合椭偏参数获得在线Low-E玻璃的光学常数及每层膜厚度,并用扫描电镜对样品的膜厚进行表征.结果表明,Lorentz双振子模型和Cauchy模型能很好地解释在线Low-E玻璃的光学特性;同时,椭圆偏振法也为多层膜系统提供了一种测定光学常数和膜厚的可靠方法.     

9,10‐Diaminoanthracenes Revisited: The Influence of N‐Substituents on Their Electronic States

The electronic and molecular structures of 9,10‐diamino‐substituted anthracenes with different N‐substituents have been re‐examined. In particular, different N‐substituents influence both the electronic and molecular structures of the oxidized species of 9,10‐diaminoanthracenes. The anthrylene moiety of 9,10‐bis(N,N‐di(p‐anisyl)amino)anthracene retains its planarity during the course of two successive one‐electron oxidations, whereas 9,10‐bis(N,N‐dimethylamino)anthracene and 9,10‐bis(N‐p‐anisyl‐N‐methylamino)anthracene undergo a substantial structural change to a butterfly‐like structure through a two‐electron oxidation process. The structural changes observed for the oxidized states are ascribed to significant differences in the frontier molecular orbitals of the above‐mentioned three kinds of 9,10‐diaminoanthracenes due to different extents of mixing between the amine‐localized and anthrylene‐localized orbitals.     

A modern approach to the solution and analysis of the Simha-Somcynsky model for the description of pressure-volume-temperature properties of polymer fluids

We revisit the Simha-Somcynsky model of polymer fluids with the purpose of developing novel theoretical and computational approaches to simplify and speed up its solution as well as the fitting of experimental data, and decrease its level of mathematical complexity. We report a novel method that allows us to solve one of the two equations of the model exactly, thus putting the level of mathematical difficulty on a par with the one of other models for polymer fluids. Moreover, we describe a computational algorithm capable of fitting all five parameters of the model in an unbiased way. The results obtained reproduce literature results and fit experimental pressure-volume-temperature and solubility parameter data for three polymers very accurately. Moreover, the new techniques allow for the investigation of the model at very low temperatures. Unexpectedly, the model predicts behaviors that could be interpreted as a glass transition, as routinely observed in dilatometry and differential scanning calorimetry, and a glass phase. We compared the predicted and experimental T g’s for cis poly(1,4-butadiene) and found an excellent quantitative agreement.     

Modulation of the Physicochemical Properties of Donor–Spiro–Acceptor Derivatives through Donor Unit Planarisation: Phenylacridine versus Indoloacridine—New Hosts for Green and Blue Phosphorescent Organic Light‐Emitting Diodes (PhOLEDs)

This work reports a detailed structure–property relationship study of a series of efficient host materials based on the donor–spiro–acceptor (D‐spiro‐A) design for green and sky‐blue phosphorescent organic light‐emitting diodes (PhOLEDs). The electronic and physical effects of the indoloacridine (IA) fragment connected through a spiro bridge to different acceptor units, namely, fluorene, dioxothioxanthene or diazafluorene moiety, have been investigated in depth. The resulting host materials have been easily synthesised through short, efficient, low‐cost, and highly adaptable synthetic routes by using common intermediates. The dyes possess a very high triplet energy (E_T) and tuneable HOMO/LUMO levels, depending on the strength of the donor/acceptor combination. The peculiar electrochemical and optical properties of the IA moiety have been investigated though a fine comparison with their phenylacridine counterparts to study the influence of planarisation. Finally, these molecules have been incorporated as hosts in green and sky‐blue PhOLEDs. For the derivative SIA‐TXO₂ as a host, external quantum efficiencies as high as 23 and 14 % have been obtained for green and sky‐blue PhOLEDs, respectively.     

Controlled Variable Oxidative Doping of Individual Organometallic Nanoparticles

The charging and controlled oxidative doping of single organometallic ferrocene nanoparticles is reported in aqueous sodium tetrafluoroborate using the nano‐impacts method. It is shown that ferrocene nanoparticles of approximately 105 nm diameter are essentially quantitatively oxidatively doped with the uptake of one tetrafluoroborate anion per ferrocene molecule at suitably high overpotentials. By using lower potentials, it is possible to achieve low doping levels of single nanoparticles in a controlled manner.